diff --git a/keyboards/daisy/config.h b/keyboards/daisy/config.h
new file mode 100644
index 0000000000..d2ab92f875
--- /dev/null
+++ b/keyboards/daisy/config.h
@@ -0,0 +1,175 @@
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0x1209
+#define PRODUCT_ID 0x2328
+#define DEVICE_VER 0x501
+#define MANUFACTURER K.T.E.C.
+#define PRODUCT Daisy
+#define DESCRIPTION qmk port for Daisy
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 11
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D2, D3, D5, B7 }
+#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B6, B5, B4, D7, D6 }
+#define UNUSED_PINS
+
+/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_PIN D0
+#define BACKLIGHT_LEVELS 6
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1 H
+//#define MAGIC_KEY_HELP2 SLASH
+//#define MAGIC_KEY_DEBUG D
+//#define MAGIC_KEY_DEBUG_MATRIX X
+//#define MAGIC_KEY_DEBUG_KBD K
+//#define MAGIC_KEY_DEBUG_MOUSE M
+//#define MAGIC_KEY_VERSION V
+//#define MAGIC_KEY_STATUS S
+//#define MAGIC_KEY_CONSOLE C
+//#define MAGIC_KEY_LAYER0_ALT1 ESC
+//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
+//#define MAGIC_KEY_LAYER0 0
+//#define MAGIC_KEY_LAYER1 1
+//#define MAGIC_KEY_LAYER2 2
+//#define MAGIC_KEY_LAYER3 3
+//#define MAGIC_KEY_LAYER4 4
+//#define MAGIC_KEY_LAYER5 5
+//#define MAGIC_KEY_LAYER6 6
+//#define MAGIC_KEY_LAYER7 7
+//#define MAGIC_KEY_LAYER8 8
+//#define MAGIC_KEY_LAYER9 9
+//#define MAGIC_KEY_BOOTLOADER PAUSE
+//#define MAGIC_KEY_LOCK CAPS
+//#define MAGIC_KEY_EEPROM E
+//#define MAGIC_KEY_NKRO N
+//#define MAGIC_KEY_SLEEP_LED Z
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+// ws2812 options
+#define RGB_DI_PIN C7 // pin the DI on the ws2812 is hooked-up to
+#define RGBLIGHT_ANIMATIONS // run RGB animations
+#define RGBLED_NUM 8 // number of LEDs
+#define RGBLIGHT_HUE_STEP 12 // units to step when in/decreasing hue
+#define RGBLIGHT_SAT_STEP 25 // units to step when in/decresing saturation
+#define RGBLIGHT_VAL_STEP 12 // units to step when in/decreasing value (brightness)
+
+/*
+ * MIDI options
+ */
+
+/* Prevent use of disabled MIDI features in the keymap */
+//#define MIDI_ENABLE_STRICT 1
+
+/* enable basic MIDI features:
+ - MIDI notes can be sent when in Music mode is on
+*/
+//#define MIDI_BASIC
+
+/* enable advanced MIDI features:
+ - MIDI notes can be added to the keymap
+ - Octave shift and transpose
+ - Virtual sustain, portamento, and modulation wheel
+ - etc.
+*/
+//#define MIDI_ADVANCED
+
+/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */
+//#define MIDI_TONE_KEYCODE_OCTAVES 1
+
+#endif
diff --git a/keyboards/daisy/daisy.c b/keyboards/daisy/daisy.c
new file mode 100644
index 0000000000..f8ca24ff0b
--- /dev/null
+++ b/keyboards/daisy/daisy.c
@@ -0,0 +1,15 @@
+#include "daisy.h"
+
+void led_set_kb(uint8_t usb_led) {
+ // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+ if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+ // output low
+ DDRC |= (1<<PC6);
+ PORTC &= ~(1<<PC6);
+ } else {
+ // Hi-Z
+ DDRC &= ~(1<<PC6);
+ PORTC &= ~(1<<PC6);
+ }
+ led_set_user(usb_led);
+}
\ No newline at end of file
diff --git a/keyboards/daisy/daisy.h b/keyboards/daisy/daisy.h
new file mode 100644
index 0000000000..7e45bee2b5
--- /dev/null
+++ b/keyboards/daisy/daisy.h
@@ -0,0 +1,19 @@
+#ifndef DAISY_H
+#define DAISY_H
+
+#include "quantum.h"
+
+#define KEYMAP( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K3A, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, \
+ K30, K31, K32, K34, K35, K37, K38, K39 \
+) \
+{ \
+ { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A }, \
+ { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A }, \
+ { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A }, \
+ { K30, K31, K32, KC_NO, K34, K35, KC_NO, K37, K38, K39, K3A } \
+}
+
+#endif
\ No newline at end of file
diff --git a/keyboards/daisy/keymaps/default/keymap.c b/keyboards/daisy/keymaps/default/keymap.c
new file mode 100644
index 0000000000..ff08cf0a8f
--- /dev/null
+++ b/keyboards/daisy/keymaps/default/keymap.c
@@ -0,0 +1,99 @@
+ #include "daisy.h"
+#include "action_layer.h"
+
+extern keymap_config_t keymap_config;
+
+// Layer shorthand
+#define _BL 0
+#define _LW 1
+#define _RS 2
+
+enum layer_keycodes {
+ QWERTY = SAFE_RANGE, LOWER, RAISE
+};
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+/* Base Layer
+ * .-----------------------------------------------------------------------.
+ * | ESC | Q | W | E | R | T | Y | U | I | O | P | \| |
+ * |-----------------------------------------------------------------------|
+ * | TAB | A | S | D | F | G | H | J | K | L | ENTER |
+ * |-----------------------------------------------------------------------|
+ * | LSHIFT | Z | X | C | V | B | N | M | ,< | .> | /? |
+ * |-----------------------------------------------------------------------|
+ * | LCTRL | LGUI | LALT | SPACE | BACKSPACE | LW | RS | RALT |
+ * '-----------------------------------------------------------------------'
+ */
+
+ [_BL] = KEYMAP(
+ GRAVE_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSLS,
+ KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_ENT,
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH,
+ KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_BSPC, LOWER, RAISE, KC_RALT ),
+
+
+/* Function Layer
+ * .-----------------------------------------------------------------------.
+ * | GRV | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | -_ |
+ * |-----------------------------------------------------------------------|
+ * | | =+ | UP | | | | [{ | ]} | ;: | '" | |
+ * |-----------------------------------------------------------------------|
+ * | | LEFT| DOWN |RIGHT| | | | | | | |
+ * |-----------------------------------------------------------------------|
+ * | | | | | DELETE | | | |
+ * '-----------------------------------------------------------------------'
+ */
+
+ [_LW] = KEYMAP(
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS,
+ KC_TRNS, KC_EQL, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_LBRC, KC_RBRC, KC_SCLN, KC_QUOT, KC_TRNS,
+ KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,
+ KC_LCTL, KC_LGUI, KC_LALT, KC_TRNS, KC_DEL, KC_TRNS, KC_TRNS, KC_TRNS ),
+
+
+ /* Second Function Layer
+ * .-----------------------------------------------------------------------.
+ * | RST | F1 | F2 | F3 | F4 | F5 | F6 | | HOME| PGUP| | |
+ * |-----------------------------------------------------------------------|
+ * | | F7 | F8 | F9 | F10 | F11 | F12 | | END | PGDN| |
+ * |-----------------------------------------------------------------------|
+ * | |RGBtog|RGBmod|RGBhud|RGBhui|RGBvad|RGBvai|RGBsad|RGBsai|BL| |
+ * |-----------------------------------------------------------------------|
+ * | | | | | | | | |
+ * '-----------------------------------------------------------------------'
+ */
+
+ [_RS] = KEYMAP(
+ RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS, KC_TRNS,
+ KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_END, KC_PGDN, KC_TRNS,
+ KC_TRNS, RGB_TOG, RGB_SMOD, RGB_HUD, RGB_HUI, RGB_VAD, RGB_VAI, RGB_SAD, RGB_SAI, BL_STEP, KC_TRNS,
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS ),
+
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ case LOWER:
+ if(record->event.pressed){
+ layer_on(_LW);
+ } else {
+ layer_off(_LW);
+ }
+ return false;
+ break;
+ case RAISE:
+ if(record->event.pressed){
+ layer_on(_RS);
+ } else {
+ layer_off(_RS);
+ }
+ return false;
+ break;
+ }
+ return true;
+};
\ No newline at end of file
diff --git a/keyboards/daisy/keymaps/default/readme.md b/keyboards/daisy/keymaps/default/readme.md
new file mode 100644
index 0000000000..dff0dcbdee
--- /dev/null
+++ b/keyboards/daisy/keymaps/default/readme.md
@@ -0,0 +1,5 @@
+
+
+# Default Daisy Layout
+
+This is the default layout as offered by KPRepublic's TMK firmware for the Daisy with a few minor tweaks for usability made by me.
diff --git a/keyboards/daisy/readme.md b/keyboards/daisy/readme.md
new file mode 100644
index 0000000000..427891d96e
--- /dev/null
+++ b/keyboards/daisy/readme.md
@@ -0,0 +1,29 @@
+# Daisy
+
+A 40% keyboard kit sold by KPRepublic.
+
+Keyboard Maintainer: westfoxtrot (https://github.com/westfoxtrot)
+Hardware Supported: Daisy PCB Rev.1, Daisy PCB Rev.2
+Hardware Availability: http://tinyurl.com/yc26lq22
+
+Make example for this keyboard (after setting up your build environment):
+
+ make daisy:default
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
+
+
+# Other Keymaps
+
+The "default" keymap included is the layout I personally use on the Daisy and the one I have found the most comfortable.
+
+A printable picture showing this layout is available here: https://imgur.com/9mSF0yf
+
+
+```
+$ make daisy:[default|<name>]
+```
+
+# Bootloader
+
+I personally had issues with the bootloader on my Daisy PCB and was unable to flash a firmware to the board after the first time. I replaced the bootloader with the one available in the repository at ../../util/bootloader_atmega32u4_1_0_0.hex
diff --git a/keyboards/daisy/rules.mk b/keyboards/daisy/rules.mk
new file mode 100644
index 0000000000..f24df2fd6c
--- /dev/null
+++ b/keyboards/daisy/rules.mk
@@ -0,0 +1,66 @@
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4996
+
+# QMK Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = no # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
+AUDIO_ENABLE = no # Audio output on port C6
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
\ No newline at end of file